Perlick PERL Keg Beer Faucet - Polished Chrome

Model: 630PC

53 Reviews

$39.00

Perlick's 630PC forward sealing faucet features a low-lead polished chrome-plated brass body
Patented forward sealing design eliminates the need for a valve shaft exposed to beer and air
Spout angle is more vertical, allowing a more thorough draining after each pour and no horizontal area for beer to collect
Polished interior ensures a smooth flow with less agitation and less foaming
This faucet is easy to clean and may be cleaned in place

DESCRIPTION

FEATURES

REVIEWS

Q&A

Unique in both appearance and function, Perlick's 630PC Forward Sealing Faucet features a revolutionary ball and floating front seal design that prevents beer from being exposed to air. As a result, the handle lever does not stick and there is no build up of mold and bacteria in the faucet body. There are also fewer internal parts, which results in better reliability and fewer service calls. The 630PC features a low-lead polished chrome-plated brass construction for economical beer dispensing.

WARNING: This product has Brass components. Brass alloys are known to contain trace amounts of Lead, which is known to the State of California to cause cancer and reproductive harm. For more information, go to www.P65Warnings.ca.gov.

All Perl faucets include a stainless steel lever for strength and sanitation.
Forward seat design to prevent lever from sticking
More sanitary than rear seating faucets
1"W x 4"H x 2 3/4"D

Faucet Replacement Parts
Item	630	680	650	690	Description
1	67829-1	67829-1	67829-1	67829-1	Handle Jacket, Chrome
1	67829-1TF	67829-1TF	N/A	N/A	Handle Jacket, Tarnish Free
2	67820-1	67820-1	67820-1	67820-1	Compression Bonnet, Chrome
2	67820-1TF	67820-1TF	N/A	N/A	Compression Bonnet, Tarnish Free
3	67828-1	67828-1	67828-1	67828-1	O-Ring, Compression
4	67819-2	67819-2	67819-2	67819-2	Bearing Cup
5A	68726-1	N/A	68626-1	N/A	Handle Lever
5B	N/A	68810	N/A	68810	Handle Lever, Push Back Creamer
6	67830-1	67830-1	67830-1	67830-1	O-Ring, Pivot Ball
7	67933-1	67933-1	67933-1	67933-1	O-Ring, Front Seat
8	308-3-2P	308-3-2P	308-3-2P	308-3-2P	Coupling Gasket
9	N/A	N/A	68206-1	68206-1	Flow Control: Compensator
10	N/A	N/A	67989SK	67989SK	Flow Control: Seal Kit
11	N/A	N/A	67989LK	67989LK	Flow Control: Lever & Seal Kit

Follow these instructions if you need to take the faucet apart to replace worn parts.

Note: Anytime the Front Seat (I), O-ring (H) or Coupling Gasket(s) are removed, they should be replaced. Always use OEM replacement parts.

TO DISASSEMBLE:

If faucet is USED, soak faucet in warm cleaning solution for 1-2 minutes to free up bonnet and handle jacket. If the faucet is NEW, submerge the faucet in warm water for 5 seconds.
Unscrew and remove Jacket (1).
Unscrew and remove Compression Bonnet (2).
Remove Coupling Gasket (8) only if cut or worn.
To remove the Handle Lever Assembly (5A or 5B), lift it upward and push back.
To remove Front Seat (7) use a small screwdriver from the bonnet end of the faucet.
To remove O-ring (6) use a small screwdriver from the bonnet end of the faucet.
Inspect O-rings for wear or damage and replace as necessary.
To remove flow control lever, unscrew cap and pull out.
Remove flow control compensator from rear of faucet.

TO ASSEMBLE:

Re-install O-ring (6) into O-ring groove from bonnet end (use a small blunt screwdriver).
Re-install front Seat (7) into O-ring groove (use a small blunt screwdriver). Note: Seat must move freely in seat groove.
Re-install Handle Lever Assembly (5A or 5B).
Re-install Bearing Cup (4).
Re-install Bonnet Washer (3) into Compression Bonnet (2).
Re-install Compression Bonnet (2). Tighten by hand only. Do not use any tool, as this can damage the faucet.
Re-install Handle Jacket (1).
Re-install Coupling Gasket (8) if removed.
Install flow control compensator into rear of faucet and orientate so level engagement hole is facing lever insertion hole.
Install flow control lever, ensure pin on end of lever is aligned with compensator engagement hole and tighten cap.

UPC: 847808038046

12/28/2023

Perlick 630SS Forward Sealing Faucet

Shiner Bock

Worth the money! You will never be happy with a standard faucet again that sticks. This Perlick faucet is so smooth!!

09/07/2023

Better faucet

Lewsh

Was using old style faucets with internal piston. This faucet has no piston, is very smooth and light in the hand to operate. So far no sticking of faucets.

05/04/2022

Riley’s Irish Pub

Mike

We serve a lot of darker larger and ale style beers. We have always struggled with the faucet gunking up just after a couple days of non use causing the faucet to stick. This style of faucet has solved that problem

12/04/2021

Commercial Grade Double Gauge Secondary

Tom

easy to install ad is a great upgrade

04/18/2020

Top quality

Tony

This product is so much bette4 then the standard tap that comes with the keg.

Showing Reviews 1-5 of 53

Question:

Where are these manufactured?

by hoobie on October 06, 2019

Answer:

Perlick products are manufactured in Milwaukee, Wisconsin

by Ben on October 10, 2019

Staff Answer

CONNECT WITH US!

@BeverageFactory

Perlick PERL Keg Beer Faucet - Polished Chrome

TO DISASSEMBLE:

TO ASSEMBLE:

CONNECT WITH US!

Added to Cart