Wholesale Pricing Available. Apply Now
Spring Into Savings | Up to 50% off!

The Ultimate Sparge Arm

Model: BE950
0 Reviews
$272.71SAVE 40% - $109.08
$163.63

90 Day Money Back Guarantee
IN STOCK (usually ships within 24 hours)
  • This sparge arm is excellent for sparging as well as recirculating your mash in a RIMS or HERMS system
  • Two adjustment points, one for holding the arm against the kettle, while the other moves up and down inside the kettle
  • Thumbscrew knobs are easily tighten and loosen by hand, so no tools are needed
  • Included 1/2" ball valve helps regulate the flow rate
  • 100% stainless and silicone construction

Made of stainless steel and silicone, this Ultimate Sparge Arm is the perfect addition to your grain set up. It has two adjustment points, where one one hold the sparge arm against the kettle, while the other allows you to move the arm up and down inside the kettle to accommodate different amounts of grain. The thumbscrew knobs are easily tightened and loosened by hand, so no tools are needed. This sparge arm is excellent for sparging as well as recirculating your mash in a RIMS or HERMS system.

Please Note: This sparge arm will not fit on most coolers.

Warning WARNING: This product has Brass components. Brass alloys are known to contain trace amounts of Lead, which is known to the State of California to cause cancer and reproductive harm. For more information, go to www.P65Warnings.ca.gov.
  • 100% stainless and silicone construction
  • Two adjustment knobs make it extremely universal
  • Included ball valve allows you to increase or decrease the flow rate during sparge or recirculation
  • Included check ball will prevent back flow
  • Can adjust from the top of your kettle to 12-13 inches down into your kettle
  • A single, large diameter outlet port trickles onto a stainless disc, which distributes sparge water gently and evenly. This port is also much easier to flush out and keep clean than many other sparge assemblies with multiple small holes that grain gets stuck in during recirculation
  • Stainless tube measures 18.5" from the top to the bend, and 8.5" from the bottom to the center of the distribution disc.
  • Can be mounted on a lip that is up to 7/8" wide
  • Has a 1/2" FPT ball valve

No customer reviews available.

Question:
Does this fit on the SS Brewtech Infusion mash tun?
by Mike on August 01, 2019
Answer:
Not intirely sure as we dont have access to the SS Brewtech Infusion Mash Tun. From the pictures I would be concerned about the distance the arm travels on this sparge arm in relation to the center of the SS brewtech mash tun. SS does make their own sparge arm if you want to check that one out and compare it to this one.
by Dave on August 10, 2019
Staff Answer

Made of stainless steel and silicone, this Ultimate Sparge Arm is the perfect addition to your grain set up. It has two adjustment points, where one one hold the sparge arm against the kettle, while the other allows you to move the arm up and down inside the kettle to accommodate different amounts of grain. The thumbscrew knobs are easily tightened and loosened by hand, so no tools are needed. This sparge arm is excellent for sparging as well as recirculating your mash in a RIMS or HERMS system.

Please Note: This sparge arm will not fit on most coolers.

Warning WARNING: This product has Brass components. Brass alloys are known to contain trace amounts of Lead, which is known to the State of California to cause cancer and reproductive harm. For more information, go to www.P65Warnings.ca.gov.
  • 100% stainless and silicone construction
  • Two adjustment knobs make it extremely universal
  • Included ball valve allows you to increase or decrease the flow rate during sparge or recirculation
  • Included check ball will prevent back flow
  • Can adjust from the top of your kettle to 12-13 inches down into your kettle
  • A single, large diameter outlet port trickles onto a stainless disc, which distributes sparge water gently and evenly. This port is also much easier to flush out and keep clean than many other sparge assemblies with multiple small holes that grain gets stuck in during recirculation
  • Stainless tube measures 18.5" from the top to the bend, and 8.5" from the bottom to the center of the distribution disc.
  • Can be mounted on a lip that is up to 7/8" wide
  • Has a 1/2" FPT ball valve

No customer reviews available.

Question:
Does this fit on the SS Brewtech Infusion mash tun?
by Mike on August 01, 2019
Answer:
Not intirely sure as we dont have access to the SS Brewtech Infusion Mash Tun. From the pictures I would be concerned about the distance the arm travels on this sparge arm in relation to the center of the SS brewtech mash tun. SS does make their own sparge arm if you want to check that one out and compare it to this one.
by Dave on August 10, 2019
Staff Answer

CONNECT WITH US!

@BeverageFactory
Added to Cart

.....