- Comes complete with a 2-tap keg beer dispense system that features 100% stainless steel contact
- Can be converted into an all-refrigerator using the two included adjustable shelves for additional refrigerated storage
- Spacious interior can accommodate full-size kegs (15.5 gallon), 1/4 beer barrels (7.75 gallon), and 5 gallon kegs
- Stylish black cabinet with reversible black door, removable drip tray, chrome guard rail, and textured serving countertop
- PLEASE NOTE: Coors kegs will not fit in this keg refrigerator
Dimensions: 33" H x 20" W x 25.5" D
This K199B-2NK Full Size Keg Beer Refrigerator from Kegco houses your kegs in a beautiful all-black cabinet and comes equipped with a Kegco Exclusive 14" tall dual tap draft tower. It also comes with two removable wire shelves that allow you to convert this keg fridge into an all-refrigerator or beverage center when you need additional cold storage. 2-1/2" casters let you move the beer keg dispenser anywhere you need it, from the bar to the living room to the patio.
Kegco has packed this K199B-2NK with many convenient features that give you the most for your money. A steel interior floor mat ensures long-lasting durability, while also allowing your kegs to glide easily when sliding them in and out of the cabinet. The textured serving countertop has an attractive metal safety rail that keeps your glasses and beer mugs from sliding off, and the easy-to-clean removable drip tray collects drips and spills to keep cleaning to a minimum. This beer cooler was designed to be ultra-quiet and 25% more energy efficient, making it ideal for use in the home.
This beer cooler was designed to be ultra-quiet and 25% more energy efficient, making it ideal for use in the home. This keg cooler can accommodate one full size, straight pony, or quarter slim keg, or up to two sixth slim, strap handle, or rubber home brew kegs. PLEASE: It will not fit bevel or rubber kegs that are wider in the middle than at the top or bottom. These are commonly used by Coors and Miller brewing companies.
- MDK-199B-01 Kegerator with Dual Faucet Dispense System
- Includes a brand new 5 lb. Aluminum CO2 Tank
This tank is produced from high strength aluminum alloy 6061-T6, a highly corrosion-resistant material. The service pressure is up to 1800 PSI/124 BAR with a test pressure of 3000 PSI/207 BAR. These cylinders are stamped with the required U.S. Department of Transportation and Transport Canada markings. The 320 valves are CGA approved, and have a male thread for CO2 regulators. An average fill is good for 5-6 kegs depending upon your fill. - Includes Commercial Grade Dual Gauge Two Product CO2 Regulator
The regulator works with any CO2 tank with a CGA-320 valve and measures PSI, as well as the volume of the CO2 gas in the cylinder. It has a pressure release valve and a large hand control which makes it easy to adjust the pressure inside the keg. - Includes two 5 foot lengths of 5/16 Inch I.D. Blue Air Line Assembly with 2 Snap Clamps
These standard 5 foot lengths of 5/16" I.D. blue air/CO2 tubing is made of thermoplastic vinyl hose (Super Vinyl). This tubing will not rot, swell, or dry out, and is unaffected by normal cleaning compounds. Each air line assembly comes with two plastic snap clamps with a reusable clamp design. - Includes two D system lever handle keg couplers
These commercial grade lever handle keg couplers work with all American "D" system Sankey kegs. They feature 55-psi pressure relief valves and nickel-plated forged brass bodies. To tap a keg, simply pull out and then down on the lever handle. - Includes a Kegco Exclusive 14" Tall, 3" Diameter Dual Faucet Polished Stainless Steel Draft Tower
This NSF-approved tower is a 3" diameter dual faucet metal draft tower made of polished stainless steel. It comes complete with two stainless steel faucets and two 5 foot lengths of 3/16" I.D. clear beer tubing. Th3 tower is mounted using the gasket and four screws that are included. This Kegco Exclusive tower measures 14" tall, giving you an extra 2" of space over standard draft beer towers to allow you to easily fill tall growlers and pint glasses. - PLEASE NOTE: Coors Kegs will not fit into this Kegerator.
- Measures at 33"H x 20"W x 25.5"D
- Reversible Door
- the Kegco K199B-1 Beer Dispenser comes with 2 full-width wire shelves and a hole plug which allows you to convert kegerator into a Compact Refrigerator.
- Includes 2 Full-width Wire Shelves
- Holds: 1/2 barrels / Full Size Kegs (15.5gal), 1/4 barrels / Ponies (7.75gal)
- Maximum Ambient Temperature: 100 degrees Fahrenheit
- Minimum Ambient Temperature: The lowest temperature you want to store your kegs at. The unit does not have a heater, so if the ambient temperature is lower than the set temperature, the internal temperature will match the external temperature.
- Removable Drip Tray with Grill to Collect spills
- Chrome Guard Rail to Protect Your Mugs and Glasses from Sliding Off
- Steel interior floor mat for long lasting durability and easy glide of beer keg.
- Textured serving counter top.
- 25% more energy efficient design saves you money each month
- UL Listed
Warranty Information:
- 1 Year Parts and Labor
- 5 Years on Compressor (parts only)
Brand | Full Size | Pony Size | Quarter slim | 5 Gallon D System | 5 Gallon Ball Lock | 5 Gallon Pin Lock | 5 Gallon Strap Handle |
---|---|---|---|---|---|---|---|
Kegco K199 |
1 | 1 | 1 | 2 | 2 | 2 | 2 |
Kegco K209 |
1 | 1 | 1 | 2 | 3 | 3 | 3 |
Kegco K309 |
1 | 1 | 1 | 2 | 3 | 3 | 3 |
Kegco VSK-15 |
0 | 0 | 0 | 1 | 1 | 1 | 1 |
Kegco SLK-15 |
0 | 0 | 0 | 1 | 1 | 1 | 1 |
Kegco Z163 |
1 | 1 | 1 | 2 | 3 | 2 | 3 |
Kegco HK38 |
1 | 1 | 2 | 3 | 3 | 3 | 3 |
Kegco XCK-1 |
1 | 1 | 2 | 4 | 4 | 4 | 4 |
Summit SBC677 |
1 | 1 | 1 | 2 | 3 | 2 | 3 |
Summit SBC635 |
1 | 1 | 1 | 2 | 3 | 3 | 3 |
Haier Kegerator |
1 | 1 | 2* | 2 | 3 | 3 | 3 |
Danby Kegerator |
1 | 1 | 1 | 2 | 3 | 2 | 3 |
All Marvel Kegerators |
1 | 1 | 1 | 2 | 3 | 3 | 3 |
Perlick HP15T |
0 | 0 | 0 | 1 | 1 | 1 | 1 |
Perlick HP24T |
0 | 1 | 0 | 2 | 2 | 1 | 2 |
Perlick HC24T |
0 | 1 | 0 | 2 | 2 | 1 | 2 |
UBC Kegmaster |
1 | 1 | 2 | 4** | 3 | 4** | 4** |
Beverage Air BM23 |
1 | 1 | 2 | 3 | 4 | 4 | 4 |
Everest EBD1 |
1 | 1 | 1 | 2 | 3 | 3 | 3 |
Brand | Full Size | Pony Size | Quarter slim |
---|---|---|---|
Kegco K199 |
1 | 1 | 1 |
Kegco K209 |
1 | 1 | 1 |
Kegco K309 |
1 | 1 | 1 |
Kegco VSK-15 |
0 | 0 | 0 |
Kegco SLK-15 |
0 | 0 | 0 |
Kegco Z163 |
1 | 1 | 1 |
Kegco HK38 |
1 | 1 | 2 |
Kegco XCK-1 |
1 | 1 | 2 |
Summit SBC677 |
1 | 1 | 1 |
Summit SBC635 |
1 | 1 | 1 |
Haier Kegerator |
1 | 1 | 2* |
Danby Kegerator |
1 | 1 | 1 |
All Marvel Kegerators |
1 | 1 | 1 |
Perlick HP15T |
0 | 0 | 0 |
Perlick HP24T |
0 | 1 | 0 |
Perlick HC24T |
0 | 1 | 0 |
UBC Kegmaster |
1 | 1 | 2 |
Beverage Air BM23 |
1 | 1 | 2 |
Everest EBD1 |
1 | 1 | 1 |
Brand | 5 Gallon D System | 5 Gallon Ball Lock | 5 Gallon Pin Lock | 5 Gallon Strap Handle |
---|---|---|---|---|
Kegco K199 |
2 | 2 | 2 | 2 |
Kegco K209 |
2 | 3 | 3 | 3 |
Kegco K309 |
2 | 3 | 3 | 3 |
Kegco VSK-15 |
1 | 1 | 1 | 1 |
Kegco SLK-15 |
1 | 1 | 1 | 1 |
Kegco Z163 |
2 | 3 | 2 | 3 |
Kegco HK38 |
3 | 3 | 3 | 3 |
Kegco XCK-1 |
4 | 4 | 4 | 4 |
Summit SBC677 |
2 | 3 | 2 | 3 |
Summit SBC635 |
2 | 3 | 3 | 3 |
Haier Kegerator |
2 | 3 | 3 | 3 |
Danby Kegerator |
2 | 3 | 2 | 3 |
All Marvel Kegerators |
2 | 3 | 3 | 3 |
Perlick HP15T |
1 | 1 | 1 | 1 |
Perlick HP24T |
2 | 2 | 1 | 2 |
Perlick HC24T |
2 | 2 | 1 | 2 |
UBC Kegmaster |
4** | 3 | 4** | 4** |
Beverage Air BM23 |
3 | 4 | 4 | 4 |
Everest EBD1 |
2 | 3 | 3 | 3 |
* - Using Wood riser for front keg
** - With external CO2 tank (3 with internal CO2 tank)
Dimensions | |
---|---|
Height | 33" |
Width | 20' |
Depth | 25 1/2" |
Weight | |
---|---|
Unit Weight | 95 lbs. |
Shipping Weight | 110 lbs. |
Warranty | |
---|---|
Labor | 1 Year |
Parts | 1 Year |
Compressor (Parts Only) | 5 Years |
Exterior | |
---|---|
Cabinet | Black Cabinet |
Drip Tray | Yes |
Guard Rail | Yes |
Casters | Yes |
Keg Storage Capacities | |
---|---|
Full Size / 1/2-Barrel | Holds 1 |
Pony Size / 1/4-Barrel | Holds 1 |
1/4-Barrel Slim | Holds 1 |
1/6-Barrel | Holds 2 |
5 gal. Ball/Pin Lock Keg | Holds 2 |
5-Liter / Mini Keg | Holds 2 |
Key Features | |
---|---|
Built-in Capable | No |
Keg Coupler | D System |
Security Lock | No |
Regulator | Dual Gauge Two Product |
CO2 Tank | 5 lb. |
Cleaning Kit | Optional Add-On |
Outdoor Use | No |
Commercial Use | No |
Door | |
---|---|
Color / Material | Stainless Steel |
Number of Doors | 1 |
Door Handle | Recessed |
Field Reversible | Yes |
Accepts Custom Overlay Panel | No |
Draft Beer Tower | |
---|---|
Number of Faucets | 2 Faucet |
Material | Stainless Steel |
Height | 14.25" |
Diameter | 3" |
Cooling System | |
---|---|
Type | Compressor |
Front Ventilation | No |
Controls | |
---|---|
Adjustable Thermostat | Yes |
Digital | No |
Electrical | |
---|---|
Electrical Requirements | 115 V, 60 Hz |
Labor - 12 Months
LIMITED ONE YEAR WARRANTYFor one year from the date of purchase by the original owner, Kegco will, at its option, repair or replace any part of the unit, which proves to be defective in material or workmanship under normal use. During this period Kegco will provide all parts and labor necessary to correct such defects free of charge, so long as the unit has been installed and operated in accordance with the written instructions in this manual. Kegco will provide you with a reasonably similar replacement product that is either new or factory refurbished. In rental or commercial use, the warranty period is 90 days. All Kegco Appliances of 3.5 cubic feet capacity or less must be brought/sent to the appliance service shop for repair.
Parts - 60 Months
LIMITED SECOND THROUGH FIFTH YEAR WARRANTY:For the second through the fifth year from date of original purchase, Kegco Products will provide a replacement compressor free of charge due to a failure. You are responsible for the service labor and freight charges. In rental or commercial use, the limited compressor warranty is one year and nine months. Cost to move the appliance to the servicers’ shop and back to the user's home, as may be required, are the user's responsibility.
Additional Details
WHAT IS NOT COVERED:- Content losses of food or other, due to spoilage.
- Incidental or consequential damages.
- Parts and labor costs for the following will not be considered as warranty:
- Door springs, and/or frames.
- Inner door panels, door rails and/or door supports.
- Light bulbs and/or plastic housing.
- Plastic cabinet liners.
- Punctured evaporator that voids the warranty on the complete sealed system.
- Repairs performed by unauthorized servicers.
- Shipping and handling costs associated with the replacement of the unit.
- Service calls that do not involve defects in material or workmanship such as customer education, door reversal, or proper installation.
- Surcharges including, but not limited to, any after hour, weekend, or holiday service calls, tolls, ferry trip charges, or mileage expense for service call to remote areas, including the State of Alaska.
- Service calls that are related to external problems, such as abuse, misuse, inadequate electrical power, accidents, fire, floods, or acts of God.
- Replacement of house fuses or resetting circuit breakers.
- Failure of the product if it is used for other than its intended purpose.
- This warranty does not apply outside the Continental USA.
06/12/2014
Good deal for money RobGreat product for the price (25% + free delivery). Two 5 gal corney kegs fit with room for 5lbs CO2 tank and a 6 pack beer. Would be nice to have 2 holes for CO2 lines so could put tank outside (easier to adjust CO2 when force carbonating). Only has one hole. Also nice that holes for tower were pre-drilled. Overall, value for money was best I could find short of building my own.
-Rob
06/03/2014
So far, so good LeeI have incorporated my Kegerator into my outside patio bar and so far it is performing great. The assembly instructions are a little sketchy but anyone with some common sense thinking would be able to figure it out. My one issue is as others have stated the plastic clamps for holding hoses together should be upgraded at supplier as plastic over time will become brittle and break, I elected to go to the local hardware and upgrade to stainless gear clamps at the get go and everything is good.
05/27/2014
better than expected wnc beer guyAs kegco products go they are as advertised. The keg holds perfect 35 degrees and it's very quiet. The only issue the taps are loose and take some work to make tight. It looks very stylish and was a breeze to setup. The setup takes 30 minutes and don't forget you need a big wrench for the CO2 tank. Couldn't be happier.
05/10/2014
Beer in the garage ranmanShipping was fast, unit is very quiet can't here it run and easy to assemble, thermostat works great coldest is 38 degrees. There are a couple issues with this fridge but overall I am very pleased. 1) They say it will hold two 1/6 kegs, I have two in it and can't quite close the door I have ratchet strap holding it closed. 2)They say if you are going to have two kegs you have to put the co2 tank inside on shelf because the hole through the back is only big enough for one hose. after talking to a few people I found out your co2 will last twice as long if it stays outside. So I took my dremmel and opened the hole so both hoses will fit and re insulated it. Now I have two kegs and co2 is mounted in rack on back. Other than that I'm very pleased. Have been using it a couple weeks now no issues.
unfortunately Sellet is not a brand we carrier, did you by chance mean Summit? if so there number is 1-800-287-8799. Hope this helped and thank you for your question.
Thank you,
Yes but you would have to clean the beverage lines as well as transition from Nitro to Co2. We would need to get a Co2 tank and well as a Co2 regulator. Possibly other pieces in order to make this happen but you could make it work. Hope this helped and thank you for your question.
Thank you,
06/14/2014
Fantastic after a little modificationThis came shipped and packaged really well from California to Florida and arrived in about a week from ordering. Setup was pretty simple, add the castors to the bottom (if you are not putting it under a counter), and attach the tower to the top. I won't go into the setup too much since you can find that info all over the place. I'll talk more about the modifications I did to make this really work well. For some more info, I've had this for a bout 6 months or less, but I have run about 8 to 10 1/6 kegs through it without any problems.
First, the good...
1. It is pretty quiet (in most circumstances)
2. It cools the area to a nice mid to high 30* range without having to modify the thermostat.
3. It will hold 2 1/6 kegs and a CO2 tank with big regulator and have room for a few extra little things (More on that later).
4. It works and you get draft beer right in your house.
Now the bad...
1. It has a REALLY LOUD vibration that occurs only if it's in just the right angle/location/something. (Solution listed below)
2. The cold plate makes a VERY LOUD popping sound. This is because it's too close to the back wall of the unit. (Solution listed below).
3. It has no fans to circulate the cold air and the contents won't get as cold or as fast. (Solution listed below).
4. The lines in the tower are still going to be warm. (Solution listed below).
Solutions via modification:
1. VIBRATION: I went to move it to try to find where exactly the vibration was coming from and after moving it maybe 1/4", it stopped and hasn't made the noise since. So placement is very important. I suspect you could still find what is vibrating and attach some dynamat or some other vibration dampening material if the location can't be altered.
2. POPPING SOUND: For this, I used some spare automotive vacuum hose I had in the garage. I cut 4 pieces off at about 1/4" lengh. I then unscrewed the cold plate from the back wall and re-attached it with a piece of vacuum hose between the plate and wall. The screw went through the natural hole in the hose. Getting the screw back in the threaded hole in the back wall was a bit tricky on a couple, but not too bad. Now it rarely makes a popping sound at all.
3. POOR CIRCULATION: I bought a AI-MPF80A2 Quiet Dual 80mm USB Fan that comes with 2 fans that are linked together with the same wire. I have one blowing from the left side toward the right by the cold plate. And the other is angled just to teh right of that one, but pointing upward. These circulate the air around the inside quite well and evenly cool the contents much quicker than without them. I only paid $15 for them and they are definitely worth it.
4. TOWER IS WARM: I bought a tower cooler. Yes, you can make one yourself, but the amount of time you save by just buying one from someone else is worth it IMHO. I have this sitting next to the other fans (The base that is) with the blower hose just slightly into the tower area and zip-tied to the beer lines. This reduces that first pour foam that you often get due to the warmer temperature beer.
I also bought some USB extension cables so I could run the power for the 2 fan accessories easily.
Another modification (If you want to call it that) is I added a Indoor/Outdoor Digital Suction Cup Thermometer for about $7.00. The suction cup doesn't stick to anything in the kegerator, but it lets me sort of hang it on one of the kegs. It shows min and max temps for the day as well as current temp. I should probably buy a few more to keep as backups since they are so cheap. But this one has worked great the entire time I've had the kegerator and I have dropped it multiple times.
Conclusion...
So with those few modifications, this afordable Kegerator does really well and suits my needs perfectly. I might mount my CO2 tank outside and run a line in to the diverter that will still be inside the unit. But I'll need to get some motivation to do that first. :)
I hope this was helpful. I would definitely recommend this unit to a friend and the modifications I did (All totaled were less than $75). Any other kegerator with those *features* built in would cost a LOT more than that.