Taprite Commercial Dual Gauge Primary Keg Beer Regulator

Model: T742

20 Reviews

$127.00SAVE 25% - $31.75

$95.25

IN STOCK (usually ships within 24 hours)

Low pressure gauge (the top gauge) indicates output pressure to keg
High pressure gauge (the side gauge) indicates CO2 tank pressure remaining
Ball-type check valve helps prevent product back-up into the regulator, a common source of malfunction
Gray polycarbonate bonnet provides easy pressure adjustment and will not chip, break, or fade
All regulators are pressure tested to assure in-field reliability

DESCRIPTION

This dual gauge regulator is loaded with features! The regulator has a large hand control which makes it easy to adjust the pressure inside the keg. This is a double gauge regulator with the main gauge indicating how much Co2 pressure is inside the keg.

Gray polycarbonate bonnet will not chip, break or fade.
Non-adjustable "shut-down" built in to the body of regulator
The high pressure ports have left-hand female threads to prevent their use as a lo-pressure outlet
The non-removable adjusting screw is designed so that when it is turned all the way in the maximum downstream delivery pressure will not exceed 50 PSIG.
Internal relief valve opens whenever delivery pressure exceeds set pressure by 15 PSIG. This feature serves as a warning that the seat or diaphragm may be worn or damaged and should be replaced.
Sintered metal flow control filter in the inlet nipple to prevent dirt and other particles from damaging internal regulator parts.
Permanent Quad-Ring Seal on inlet nipple helps eliminate a source of leaks... no need to use a new fiber washer each time tank is changed.
Outlet features NADS 1600C shutoff which eliminates a source of gas leaks. The ball-type check valve helps prevent product back-up into the regulator, a common cause of malfunction in the regulating and relief valve parts. Hose barb end designed for use with 5/16" I.D. pressure tubing.
All regulators are pressure tested to assure in-field reliability.
Seat assembly is easily replaceable in-field... no need to remove regulator from tank.

WARNING: This product has Brass components. Brass alloys are known to contain trace amounts of Lead, which is known to the State of California to cause cancer and reproductive harm. For more information, go to www.P65Warnings.ca.gov.

REVIEWS

11/10/2014

Good Primary Regulator

PaulKegger

I have a three tap keggerator and this works good with a short tube connecting the 3 guage. Only challenge is with the knob when pushing it back in lock possition it makes really fine adjustments challenging, but not impossible.
All in all, it's what I needed and it works well!!

10/26/2014

Finally a good regulator.

TED

After two cheap regulators this one works like it should.

08/06/2014

Works great so far

Matt

I am running a quarter and a half on a 20lb tank. I like the fact I can monitor tank pressure as well as use the dial to change line pressure. The dial is much easier than a screw type to make adjustments.

Shipping was much quicker than I expected so that was also a plus for me.

05/30/2014

Taprite T742 - Commercial Dual Gauge Reg

Jerry

Had a foam problem, and Cary pointed me to this new regulator. Problem solved! Great price too!

04/30/2014

Great Product

Kalonie

Bought this to go along with my purchase of a 15 lb C02 tank. The PSI is perfect for my carbonating water and soda.

Showing Reviews 6-10 of 20

Q&A

Be the first to ask a question.

Gray polycarbonate bonnet will not chip, break or fade.
Non-adjustable "shut-down" built in to the body of regulator
The high pressure ports have left-hand female threads to prevent their use as a lo-pressure outlet
The non-removable adjusting screw is designed so that when it is turned all the way in the maximum downstream delivery pressure will not exceed 50 PSIG.
Internal relief valve opens whenever delivery pressure exceeds set pressure by 15 PSIG. This feature serves as a warning that the seat or diaphragm may be worn or damaged and should be replaced.
Sintered metal flow control filter in the inlet nipple to prevent dirt and other particles from damaging internal regulator parts.
Permanent Quad-Ring Seal on inlet nipple helps eliminate a source of leaks... no need to use a new fiber washer each time tank is changed.
Outlet features NADS 1600C shutoff which eliminates a source of gas leaks. The ball-type check valve helps prevent product back-up into the regulator, a common cause of malfunction in the regulating and relief valve parts. Hose barb end designed for use with 5/16" I.D. pressure tubing.
All regulators are pressure tested to assure in-field reliability.
Seat assembly is easily replaceable in-field... no need to remove regulator from tank.